Skip to content

Gateway Operator Setup

How to connect, identify and operate a flashed RaceLink Gateway. For firmware build / flash instructions see README.md.

Audience. Operators who already have a flashed gateway and want to use it. If you need to flash one first, start with README.md.

What you need

  • A flashed RaceLink Gateway dongle (DEV_TYPE_STR="RaceLink_Gateway_v4" for the current build; older device-type strings work as long as the wire-protocol version matches).
  • A USB cable connecting the gateway to the host machine.
  • A running RaceLink host — either standalone (racelink-standalone) or RotorHazard with the RaceLink_RH_Plugin loaded.

First-time connection

  1. Plug the dongle into the host before starting the host. The host auto-discovers the gateway on startup. If you plug it in afterwards, the host's reconnect logic finds it within a few seconds — but the master pill briefly shows LINK_LOST first.
  2. Identify the serial port.
  3. Linux: /dev/ttyUSB0 or /dev/ttyACM0 (run ls /dev/ttyUSB* /dev/ttyACM* to confirm).
  4. Windows: a COM port such as COM3 or COM4. Confirm in Device Manager. The host uses serial.SerialException's exclusive-open mode, so no other process can hold the port.
  5. Confirm the master pill goes IDLE. The pill in the WebUI header should turn cyan (IDLE) within a second of the page load. If it stays in UNKNOWN, click the ↻ refresh button next to it.

See ../RaceLink_Host/webui-overview.md §"The master bar — gateway badges" for the full state-by-state operator playbook.

OLED indicator

The gateway has a small SSD1306 OLED. The current firmware shows:

  • TX / RX counters since power-on.
  • Recent packet debug output (transient).

The OLED is informational; the master pill in the WebUI is the source of truth for gateway state.

Radio defaults

The gateway operates with the following defaults (configured at build time in platformio.ini; see README.md for the full list):

Parameter Value
Frequency 867 700 000 Hz
Bandwidth 125 kHz
Spreading factor SF7
Coding rate 4/5
Preamble 8
Sync word 0x12

These values must match the WLED nodes' build profile; see ../RaceLink_WLED/README.md §"Build profile notes".

Regional note. The default frequency is in the EU 868 MHz ISM band. Operators outside the EU must adjust the frequency in the gateway's platformio.ini and re-flash; the WLED nodes need a matching change in their build profile. There is no runtime way to change the radio band.

Pairing nodes to a gateway

A WLED node is paired to one gateway by MAC at first boot. To pair a freshly-flashed node to your gateway, simply run Discover Devices from the host's WebUI: the node listens for any broadcast and pairs with whichever gateway sent the discovery.

To migrate a node between gateways, use the WebUI's Forget master MAC option (in the Node Config dropdown) on the node, then re-discover from the new gateway. See ../RaceLink_Host/device-setup.md §"Node config — single-shot commands".

Gateway ownership rules

Only one process can hold the dongle's USB port at a time — the host opens it with exclusive=True. Running racelink-standalone and a RotorHazard plugin instance against the same dongle therefore fails the second starter with PORT_BUSY.

The full rule set (standalone vs. plugin ownership, release on shutdown, the two-process pitfall) lives in ../RaceLink_Host/architecture.md §"Gateway Ownership".

Common problems

  • The OLED stays blank. Verify the OLED pin definitions and display wiring. The OLED is non-essential — the gateway operates without it — but its absence often signals a power or wiring issue.
  • Master pill flips between IDLE and ERROR rapidly. USB hiccup. The pill returns to IDLE within seconds; it the oscillation continues, swap the USB cable or try a different USB port (a powered hub helps on some hosts).
  • PORT_BUSY banner persists after closing the other process. Some operating systems take a few seconds to release the device. Wait, then click Retry connection.

For the broader operator-side troubleshooting index see ../troubleshooting.md.